Front lamps

Model with halogen headlamps

1. Direction indicators (HP24 amber-24W).
2. Dipped beam headlamps (H7-55W).
3. Main beam headlamps (H7-55W).
4. Daytime running lamps (HP24-24W).
5. Foglamps (PS24-24W).
6. Sidelamps (W5-5W).

Model with xenon and directional headlamps

1. Direction indicators (HP24 amber-24W).
2. Dipped / main beam directional headlamps (D1S-35W).
3. Daytime running lamps / sidelamps (P21/5W).
4. Foglamps (PS24-24W).

Risk of electrocution

Xenon bulbs (D1S-35W) must be replaced by a PEUGEOT dealer or a qualified workshop.

The headlamps are fitted with polycarbonate glass with a protective coating:

do not clean them using a dry or abrasive cloth, nor with a detergent or solvent product, use a sponge and soapy water or a pH neutral product,
when using a high pressure washer on persistent marks, do not keep the lance directed towards the lamps or their edges for too long, so as not to damage their protective coating and seals,
do not touch the bulb directly with your fi ngers, use lint-free cloths.

Changing a bulb should only be done after the headlamp has been switched off for a few minutes (risk of serious burns).
It is imperative to use only anti-ultraviolet (UV) type bulbs in order not to damage the headlamp.
Always replace a failed bulb with a new bulb with the same type and specification.

Changing direction indicator and daytime running lamp bulbs (models with halogen headlamps)

Contact a PEUGEOT dealer or a qualified workshop.

Changing dipped beam headlamp bulbs (models with halogen headlamps)

Remove the protective plastic cover by pulling on the tab.

Disconnect the bulb connector.
Extract the bulb by pulling and change it.

To Refit, carry out these operations in reverse order.

Changing main beam headlamp and sidelamp bulbs

Remove the protective plastic cover by pulling on the tab.

Disconnect the bulb connector.
Remove the bulb by pulling and change it.

To Refit, carry out these operations in reverse order.

Changing dipped beam and main beam headlamp bulbs (models with xenon headlamps)

D1S xenon bulbs must be changed by a PEUGEOT dealer or a qualified workshop as there is a risk of electrocution.
It is recommended that the D1S bulbs are changed at the same time when one of them fails.

Changing sidelamp and daytime running lamp bulbs (models with xenon headlamps)

Remove the protective plastic cover by pulling on the tab.

Disconnect the bulb connector.
Remove the bulb by pulling and change it.

To Refit, carry out these operations in reverse order.

Changing direction indicator bulbs

Contact a PEUGEOT dealer or a qualified workshop.

Changing integrated direction indicator side repeaters

Insert a screwdriver towards the centre of the repeater between the repeater and the base of the mirror.

Tilt the screwdriver to extract the repeater and remove it.
Disconnect the repeater connector.

To Refit, carry out these operations in reverse order.

Contact a PEUGEOT dealer or a qualified workshop to obtain replacement repeaters.

You can also contact a PEUGEOT dealer or a qualified workshop to have these bulbs changed.

Changing foglamp bulbs

Contact a PEUGEOT dealer or a qualified workshop.

Rear lamps

1. Brake lamps / sidelamps (P21-5W).
2. Reversing lamps (P21W).
3. Direction indicators (PY21W-21W).
4. Sidelamps (P5-5W).
5. Foglamps (P21W).

Changing brake lamp/sidelamp, reversing lamp and direction indicator bulbs

Remove the plastic cover.

Remove the two lamp unit fixing nuts.
Extract the lamp unit carefully from the outside.
Disconnect the electrical connector.

Press the six tabs and remove the bulb holder.

Turn the bulb a quarter of a turn and change it.

To Refit, carry out these operations in reverse order.

Changing sidelamp bulbs (boot)

Open the boot.

Remove the plastic flap using a screwdriver.

Remove the lamp fixing nut.

Turn the bulb a quarter of a turn and change it.

To Refit, carry out these operations in reverse order.

Changing foglamp bulbs

Reach under the bumper.

Turn the bulb a quarter of a turn and pull it out.

Changing the third brake lamp bulb

Open the boot and remove the upper seal.

Unscrew the two nuts.

Press the threaded pins while supporting the lamp from the outside.

Disconnect the connector and remove the screenwash pipe.

Press the pairs of clips A then B then C to detach and gain access to the bulb holder.

Changing the number plate lamp bulbs (W5-5W)

Insert a thin screwdriver into one of the outer holes of the lens.

Push it outwards to unclip.

Remove the lens.

Pull the bulb out and change it.